Yaskawa AC Drive Z1000 Bypass Technical Manual Instrukcja Użytkownika Pobierz pdf (Strona 209)

Setting 37: Run Reverse (AUTO Mode)

Starts and stops the bypass in reverse when Z1-08 is set to 1.

Z2-09 to Z2-16: Digital Input 1 to 8 Invert Select

No. Name Setting Range Default

Z2-09 Digital Input 1 Invert Select 0, 1 0

Z2-10 Digital Input 2 Invert Select 0, 1 0

Z2-11 Digital Input 3 Invert Select 0, 1 0

Z2-12 Digital Input 4 Invert Select 0, 1 0

Z2-13 Digital Input 5 Invert Select 0, 1 0

Z2-14 Digital Input 6 Invert Select 0, 1 0

Z2-15 Digital Input 7 Invert Select 0, 1 0

Z2-16 Digital Input 8 Invert Select 0, 1 0

Bypass Digital Input Invert Settings

Table 5.29 Bypass Digital Input Invert Settings

Setting Function Page

0 Normal 209

Setting Function Page

1 Inverted 209

Setting 0: Normal

Lack of input signal = OFF

Setting 1: Inverted

Lack of input signal = ON

Z2-23 to Z2-26: Digital Output 7 to 10 Function Select

Note: Setting 23 has been added in bypass controller software version VST800298. Setting 23 is not available in bypass controller software

versions VST800297 and earlier.

No.

Name Setting Range Default

Z2-23 Digital Output 7 Function Select 0 to 23; 99 7

Z2-24 Digital Output 8 Function Select 0 to 23; 99 10

Z2-25 Digital Output 9 Function Select 0 to 23; 99 12

Z2-26 Digital Output 10 Function Select 0 to 23; 99 15

Bypass Digital Output Terminal Settings

Table 5.30 Bypass Digital Output Terminal Settings

Setting Function

0 Serial Comm Controlled

1 K1 Drive Input Contactor

2 K2 Drive Output Contactor

3 K3 Bypass Contactor

4 K4 Motor 1 Select

5 K5 Motor 2 Select

6 READY (Drive and Bypass)

7 RUN Active (Drive or Bypass)

8 Drive RUN Active

9 Bypass RUN Active

10 HAND Mode Active

11 OFF Mode Active

12 AUTO Mode Active

13 Drive Mode Selected

14 Bypass Mode Selected

Setting Function

15 Drive or Bypass Fault Active

16 Drive Fault Active

17 Bypass Fault Active

18 Auto Transfer Active

19 Serial Run Command Active

20 Damper Actuator Output

21 ON Always

22 Loss of Load Detected

<1>

Run Verify

The digital output closes when the drive or bypass output

current exceeds 10% of the value set in E2-01.

The digital output opens when the drive or bypass output

current falls below 5% of the value set in E2-01.

Not Used (Through Mode)

This setting allows serial communications to control the

output.

5.15 Z: Bypass Parameters

YASKAWA ELECTRIC SIEP YAIZ1B 01D YASKAWA AC Drive – Z1000 Bypass Technical Manual

209

Programming

1 2 ... 204 205 206 207 208 209 210 211 212 213 214 ... 461 462

Komentarze do niniejszej Instrukcji

Brak uwag

Yaskawa AC Drive Z1000 Bypass Technical Manual Instrukcja Użytkownika Strona 209

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Ekwipunek Yaskawa AC Drive Z1000 Bypass Technical Manual